Woodworking is an awesome hobby that leaves you open to so many different options that it could never get old. If you find that you are in a rut when it comes to the skills that you have you should read the article below. It is full of ideas that can bring new elements into the work that you do.
A great tool for setting crosscut guides is a stair gauge. Clamp these gauges to the carpenter’s square you have and be sure they’re matching up to the stair jack’s run and rise. Then you simply mark where the notches are. You will make a crosscut guide for your circular saw when you put it on the carpenter’s square.
Did you know that the height of your workbench is vital to the quality of work you produce? Measure where your waist is from the floor. This is how tall your bench should be.
Before you cut into a piece of wood, you need to inspect it to make sure there are not any pieces of metal in the wood. Screws, nails, staples and other metallic object will not only damage your blades, but also pose a safety hazard. Always inspect the wood before you cut.
Always check your tools before you begin using them. Woodworking with a faulty or overused tool can easily lead to a serious injury or destruction of your materials. To make sure that this does not happen to you take the time to thoroughly inspect your tools from top to bottom.
If you are new to woodworking, stick with a cheap and effective tool bag. Many of the tools to start with are under a couple hundred dollars and very easy to find and use for basic projects. These tools include a benchtop tablesaw, a jigsaw or sabre saw, a circular saw, a random orbit sander, a corded or cordless drill, a fixed-base or plunge router, and a pipe and small bar clamps.
You can apply stain with either a brush, or a rag. Work the stain in against the grain, and with it as well. You need not be neat, just get a smooth, even coat on the wood. Then, wipe immediately for a lighter tone, or leave it on for up to fifteen minutes before wiping for a deeper tone.
When wiping excess stain off wood, wipe in the direction of the grain. Otherwise, the stain will just lay on top. Not only does this ensure that the stain is getting all the way into the grain, it will show off the grain of the wood to its best advantage.
Are any of your friends, co-workers or family trying to sell their house? You may be able to increase the value of your house with your skills. You can do anything from just a new mailbox post to as much as redoing their kitchen cabinets and drawers.
Wear goggles when you are working on your pieces. Wood might fly toward your face at any time, and you want to avoid a trip to the emergency room. You might not think that it is a possibility, but this is one time when it is really important to be cautious.
Go to the art supply store and get a drafting square. Carpenter squares are a hassle, and drywall squares are notoriously inaccurate. When you need an exact square several feet in width and length, a drafting square is a surefire winner. Once you use it a few times, you’ll likely use it just as much as a tape measure.
Make sure there are no spots of glue on the wood before proceeding to finish your project. The spots will show up as lighter spots after the finish has been applied. You can use mineral spirits of naptha to completely remove all traces of glue from the wood. You may also be able to remove the glue by sanding the wood.
When you start sanding, always use a fresh sheet of sanding paper. Using fresh sandpaper allows you to get the sanding done more quickly. It is also easier to sand with fresh sandpaper. Also, while sanding it is a good idea to check the sandpaper occasionally for clogging so you can change it as needed.
When using a table saw, use a block of wood clamped to the fence to set your length. Using the fence directly could result in a board being kicked back at you. To make measurements easy, use a block that is exactly 1 inch in length. Then all you have to do is set the fence length 1 inch greater than your desired length.
Buy quality tools. There are discount tools on the market, and you may be tempted to save some money. What is the difference? Sometimes the steel in a screwdriver is softer and can strip the screw heads. Sometimes the build quality is cheap and the head of a hammer may fly off. Spend the money for good tools and you’ll have them for decades.
Some woodworkers look for perfect boards with no knots or blemishes for their projects. Using imperfect boards can add character to the finished piece so long as the defect does not compromise stability. Wood that shows whorls or burls can be used to create beautiful pieces that demand a high price when sold.
Always have a sharp blade when you’re working with skill saws or table saws. Dull blades can cause accidents. That dull blade can make the wood you are working kick back or splinter. This will yield accidents that can cause serious injuries. Also, make sure drill bits are extremely sharp in order to get the best results.
Now that you have read the article above you surely have realized that you have so much more available to work with than you thought before. The key to keeping your hobby interesting is to continue to learn about your options, just as you have by reading the above article. Now get out there are put the above tips to work.
